Art of the Craft logo Art of the CraftMade by hand, shown honestly
Sewing and Textiles

How to Reupholster a Drop-In Dining Chair Seat Pad

I bought six oak dining chairs at a house clearance for 40 pounds because the frames were sound and the joints were tight.

A dining chair seat pad face down on a garage workbench with wool fabric pulled over new foam and wadding, an electric stapler and pulled staples beside it

I bought six oak dining chairs at a house clearance for 40 pounds because the frames were sound and the joints were tight. The seats were another matter: brown moquette, worn through at the front edge on four of them, and one pad where somebody had stapled a vinyl offcut over the top of the original fabric with about ninety staples. My joinery class students kept asking why I had not fixed them, so one Sunday I did all six.

Recovering a drop-in seat is the one upholstery job a woodworker can do without learning upholstery. The pad lifts out of the frame, it is a flat plywood or beech panel with padding stapled to it, and the whole thing is held together by tension and corners. The parts that go wrong are the corners and the staple line, and those are the parts most guides rush through.

What You Are Actually Holding When the Pad Comes Out

Turn the chair upside down and the pad usually drops free, or there are four screws up through corner blocks. Underneath you will find layers in a predictable order, and the order tells you how old the chair is.

A pre-war chair has jute webbing tacked across a rebated beech frame, hessian over that, horsehair or coir fibre, a layer of cotton wadding, then calico, then the top fabric. A 1960s or later chair usually has a plywood or chipboard base with a single slab of foam glued on, then a thin polyester wadding and the cover. The second kind takes about 40 minutes a seat. The first kind can take three hours and deserves the time.

Check the base before you commit. Chipboard that has absorbed damp crumbles where the staples go, and there is no fixing it. Cutting a new base from 9 mm birch plywood takes ten minutes on a jigsaw if you use the old one as a template, and costs maybe 4 pounds of material per seat. I replaced two of my six and the difference in how the pad sits in the frame is obvious.

Foam, Fibre and What the Numbers Mean

Foam is sold by density in kilograms per cubic metre, and the density matters more than the thickness. A 28 kg per cubic metre foam feels fine for the first year and then develops a dish where everyone sits. Dining seats want 35 to 40 kg per cubic metre at 25 to 40 mm thick. Reflex foam at 50 and up is firmer than most people want under a dining chair, though it is the right choice for a hall bench that gets sat on with coats.

Cut foam about 6 mm larger than the base all round so it compresses slightly against the frame rebate and does not leave a soft edge. A bread knife cuts foam better than any blade I own, and an electric carving knife is better still if you can find one in a charity shop for 5 pounds.

Over the foam goes a layer of polyester wadding, 100 to 150 grams per square metre, wrapped over the edges and stapled on the underside. This is the layer people skip. Without it the foam grabs the cover fabric, the fabric cannot slide, and every time someone shifts their weight the cover works loose at the back. Wadding is about 3 pounds a metre and it is the cheapest improvement available.

Why Stripping Back to the Frame Is Not Always Right

Every upholstery book tells you to strip the pad to bare wood and start over. For a horsehair and webbing seat, yes, because webbing stretches and old hessian tears and you cannot assess what you cannot see. For a late plywood pad with dry, intact foam and a clean calico, I think the advice is wrong, and I say that having stripped eleven of them before I changed my mind.

Here is the reasoning. Every strip and recover cycle puts another forty to sixty staples into a 9 mm panel, usually in roughly the same line, and plywood that has been stapled four times along one edge starts to delaminate. The pad then sits loose in the rebate and rattles. Leaving sound layers in place and stapling the new cover slightly inboard of the old line gives you a seat that is firmer and a base that survives another two recovers.

The test I use is smell and squeeze. Press the foam with a thumb and let go: if it returns in under a second and the surface does not shed orange crumbs, it is fine. If it smells of damp or anything sweetish, strip it, because that is foam breaking down and it will be dust in two years. Mouse evidence means strip and bin everything, no argument.

I will concede the honest cost of my shortcut. You cannot see whether the base is cracked under the foam without lifting it, so if a seat flexes when you press the middle, strip it anyway and look.

The Order of Work, Corners Last

Fabric first: for dining chairs you want something rated for upholstery, 40,000 Martindale rubs or more for a family table. Measure the pad, add twice the pad thickness plus 50 mm on each side, and cut square to the weave rather than to the pattern. On a 420 mm square pad with 30 mm foam that comes out around 580 mm square per seat, so a 1.4 metre wide roll gives four seats from 1.2 metres if you plan the layout.

  1. Pull the old staples with an upholstery staple lifter and pliers. A flat screwdriver tears the base. Count them out of the bin so none end up in the carpet.
  2. Mark the centre of each edge of the base in pencil, and the centre of each edge of the fabric. Those four marks keep the pattern straight better than any amount of eyeballing.
  3. Lay the fabric face down, wadding and foam on top, base on top of that, and pull one long edge over. Three staples at the centre only.
  4. Go to the opposite edge, pull the fabric tight enough to flatten the wadding, and put in three staples at that centre. Check the face. Adjust now, because this is the last easy moment.
  5. Do the same on the two short edges, three staples each, then check the weave for drift. A thread line running at an angle across a seat is the thing that makes a recovered chair look homemade.
  6. Work outward from each centre toward the corners, a staple every 30 to 40 mm, alternating sides so the tension stays even. Stop 60 mm short of each corner.
  7. Corners: pull the point straight up and staple it once, then fold the two sides in as a single flat pleat each, like wrapping a parcel, and staple each fold twice. Trim the bulk inside the fold, not outside it.
  8. Trim the surplus fabric to about 15 mm from the staple line, and if the underside will be visible, staple a dust cloth over it.

A manual staple gun with 8 mm staples works, though your hand will know about it by the sixth seat. I use an electric stapler with 10 mm staples and I stopped resenting the job. If you are piecing a cover out of remnants rather than buying a roll, the fabric handling side of that is in sewing upholstery offcuts on a home machine.

What It Cost Me and What I Would Change

Six seats: 7.2 metres of a wool blend at 22 pounds a metre came to 158 pounds, foam for four seats 46 pounds, wadding 11 pounds, plywood for two bases 9 pounds, staples 4 pounds. That is 228 pounds against 40 pounds for the chairs, and one Sunday plus an evening. New chairs of that quality run well past 900 pounds for six.

What I would change: I cut all six covers before I upholstered the first one, and seat four showed me that my allowance was 20 mm tighter than it needed to be at the corners. Cut one, fit it, then cut the rest. The other thing is thread, which matters if you decide to piece or pipe anything, and the sizing logic for that is covered in needle and thread weight for a fabric. The rest of the cloth side of the workshop lives in sewing and textiles.

FAQ

Can I staple over the old fabric instead of removing it?

On a plywood base with one previous cover, yes, and it saves the base from more staple holes. With two or more covers already on there the pad becomes too thick for the frame rebate and the seat sits high. Count the layers at a corner before deciding.

How much fabric do I need for four dining chairs?

Roughly 1.2 to 1.5 metres of 1.4 metre wide fabric for four pads up to 450 mm square, assuming a plain or small pattern. A large repeat can double that, because every piece has to be cut to the same point in the pattern.

Do I need a staple gun or will tacks do?

Tacks work and look right on a period chair, but they split thin plywood and take practice to drive straight. For a modern base, staples are stronger per hole and far quicker. I keep tacks for frames with a proper beech rebate.

Why does my recovered seat not drop back into the frame?

Almost always too many layers or staples standing proud at the corners. Flatten the corner folds, trim the bulk inside the fold, and check that no staple sits on the outer vertical face of the base rather than the underside.

OB
Otis Bramwell

Otis builds furniture in a one car garage workshop and teaches a weekend joinery class on the side. He writes about wood the way he teaches it, slower than most guides and honest about the cuts that go wrong first.

More posts by Otis

More in Sewing and Textiles

01doorganico 084goad 3hot8 4465456 after5internprogram ahandfulofblessings ahmadpc ahomcybersecurity allodialresources annodex antiquesandperiodcollectibles asianworldkashmir beedlectrics bloggertemplatefree bluefeatheragency bodyweightsolution campaign08blog carfixadvisor catstreetcollective cbstvsports cnfanspurchasing committeeof500yearsofdignityandresistance covertopsdjs cs-kaiyuangame cuestacomunicaciontotal cxoutlet dancebetgame deskgearhub destinyvillastay detectmagazine di33 diamondsteelbuildings donmo dyanadropship emarsysfinance emimattl escapechan eskitarih evautoplay everythingweddings-orlando farmzone feedviewerapp foxstudiosscratch gamevui123 gleasongrade greetingsday hacklabasu haskell iw-kaiyun jagoanproperti jilidskripsi joltbusinessfinance juegodepokergratis juegospucca kaeru-festival latestmehndidesigns lestanzediottaviano litemagazines localcommunityhero lustrsazan mariashebets menswheels newwebstechs1 nikkit ootheday oxigenvpn plurfitness prefetial probudgetcarpetcleaning psychicmrsmartin pyaten qvantor rejoignezlogis rexzbot riselayouts ruchin rwxqsgd5 sakaltime shibiaowang shop-bot skrtips spotlesshaven strcoding tetapatrium topselller uneplanteartificielle vipertechcr webtech1223411 wo-kygaming yamaha-mekar yeknava yoybuysheets zenunwa yamaha-mekar jilidskripsi ankertoto ankertoto