Art of the Craft logo Art of the CraftMade by hand, shown honestly
Upcycling

Saving Hardware From Old Furniture Before You Scrap It

I put a 1930s oak chest on the kerb once with all eight drawer pulls still on it. A neighbour took the pulls off with a screwdriver in about four minutes and left the carcass sitting there.

A garage workbench with salvaged brass drawer pulls, steel butt hinges and sorted slotted screws laid out in labelled jars beside a hollow ground screwdriver

I put a 1930s oak chest on the kerb once with all eight drawer pulls still on it. A neighbour took the pulls off with a screwdriver in about four minutes and left the carcass sitting there. Two weeks later I paid $11 each for near enough the same pulls at a salvage yard to finish a different piece, and I have thought about that trade every time I break down a piece of furniture since.

Hardware is the part of an old piece that almost always outlives the wood. The brass is thicker, the steel is better, the castings have detail nobody pays for now, and the screws are made of metal that holds a slot. If a piece is beyond saving, the forty minutes you spend taking the metal off it is the highest paid work in the whole project.

Get the screws out without destroying them

Old screws have a single straight slot, and a modern tapered driver sits in that slot on two tiny points of contact. That is how slots get chewed. The fix costs about $12: a hollow ground driver, sometimes sold as a gunsmith screwdriver, where the blade sides are parallel so the tip fills the full width and depth of the slot. It is the only specialist tool in this article and it has saved me more hardware than everything else combined.

Before you turn anything, break the bond. A century of shellac, wax and grime glues the screw head to the surrounding wood, and the first quarter turn is where heads shear off. Press the tip of a soldering iron against the screw head for fifteen or twenty seconds and the heat travels down the shank and cracks that bond. Then seat the driver, press down hard, and tighten a few degrees before you loosen. Those few degrees are what frees the threads.

If the head still refuses, there are two more moves before you drill. Tap the driver handle once with a mallet while it sits in the slot, which shocks the threads loose, or run a drop of penetrating oil around the head and leave it overnight. I have a 1 in 6 failure rate on heavily painted hardware and I accept it, because the alternative is sacrificing a good hinge to save a ten cent screw.

Count and bag as you go. One zip bag per component, a strip of masking tape with the location written on it, and the screw length written next to that. Mixed screws are the reason reassembly takes three times longer than teardown, and I learned it the slow way on a wardrobe with four slightly different hinge screw lengths.

What is worth the effort and what is not

ItemKeep it?How to cleanWhat new costs
Cast brass pulls and bailsAlwaysHot water, dish soap, soft brush$8 to $18 each
Pressed steel butt hingesUsuallyVinegar soak, then oil$4 to $9 a pair
Slotted steel screwsYes, sort by lengthWire wheel at low speed$14 for a mixed tin
Cup and stem castersYes if they rollDegrease, repack the bearing$6 to $12 each
Escutcheons and keyhole platesYes, tiny and scarceSoap, never abrasive polish$5 to $15 each
Zinc pulls from the 1990sNoNot worth the bench time$2 each
Cam locks and dowel nutsNoRecycle the metalPennies
Plastic clad concealed hingesOnly matching setsWipe, check the clip$3 to $6 a pair

The magnet test settles the first question in a second. If a magnet grabs a shiny yellow pull, it is brass plated steel, and once that plating wears through there is nothing underneath worth having. Solid cast brass ignores the magnet and will clean up to something you would pay for.

Cleaning, where most people go too far

The internet consensus is to soak everything in vinegar and then polish it bright. That advice ruins more hardware than rust does.

Plenty of old brass left the factory with a lacquer coat or a deliberately darkened japanned finish, and a vinegar bath strips both. Once you have polished a set of 1890s bail handles to a mirror, you cannot put the darkness back in the recesses where it belonged, and the piece looks exactly like what it is: old furniture wearing new jewellery. For brass my whole routine is hot water, a drop of dish soap, a toothbrush, and a dry cloth. If grime fills the detail, a wooden toothpick, nothing harder.

Steel is different because rust genuinely has to come off. White vinegar with a spoon of salt, overnight, then a rinse and a hard wipe with oil before the flash rust sets in, which takes under an hour in a damp garage. Commercial chelating rust removers work better and cost about $25 a quart, and they are worth it for a box of hinges rather than one. Either way the steel comes out grey and matte, not bright, and that is correct.

One judgement call lives behind all of this. If the piece turns out to be genuinely old and intact rather than broken, the hardware belongs on it, and the whole question becomes whether to upcycle at all or leave it alone. I have stripped exactly one piece I now wish I had left whole, and that is one too many.

Why I stopped buying new pulls for old drawers

The standard advice for a dated piece is to swap the hardware, because new handles are the cheapest transformation available. I taught that line in a weekend class two years ago and I would not teach it again.

The problem is hole spacing. Old bail pulls were made on imperial centres, commonly 2 1/2 inch or 3 inch, and modern pulls come at 3 inch or 96 mm or 128 mm. The 96 mm pull misses a 3 inch hole by about 2 mm per side, which is just enough that the posts will not pass through. So you drill. Now a drawer front with a 1920s veneer has two fresh holes in it, the old ones show as dark circles under any finish you apply, and you have taken value out of the piece to install hardware that will be loose in five years because the castings are thin.

Where a swap does make sense: a flat pack carcass with no history, a piece where the original hardware is missing entirely, or a child's dresser where safety wins. Everywhere else I now reuse what came off, and if I am short a pull I buy one salvaged match rather than eight new ones.

Something worth doing this week if you have a box of mixed salvage. Sort it by type into labelled jars, measure the hole centres on every pull with a caliper and write the measurement on a tag, and photograph the jars. Mine took an evening and a roll of masking tape, and it has turned into the first place I look before any stripping or refinishing job starts. A matched set in a jar is worth real money. The same metal loose in a bucket is scrap.

FAQ

How do I get a screw out when the head has already broken off?

Drill a shallow pilot beside the shank, dig out a little wood with an awl, and grip the shank with locking pliers. If it will not turn, punch it deeper and plug over it. Chasing a broken shank through good timber does more damage than leaving it buried.

Is old hardware strong enough to reuse structurally?

Hinges and casters almost always are, and they were usually made from heavier stock than their modern equivalents. The exception is anything with a cracked casting or an elongated screw hole, since that hole will keep growing under load.

Where do salvaged pulls sell, and for how much?

Matched sets of four or eight move well at local architectural salvage and through craft and restoration groups, usually $6 to $15 a piece for solid brass. Single orphan pulls sit unsold for months, which is why sorting into sets matters more than cleaning them.

Can I use modern screws with salvaged hinges?

Mechanically yes, visually no. A Phillips head next to a row of slotted screws is the detail people notice without knowing why, and the right driver plus a tin of salvaged slotted screws costs less than replacing the hinge.

OB
Otis Bramwell

Otis builds furniture in a one car garage workshop and teaches a weekend joinery class on the side. He writes about wood the way he teaches it, slower than most guides and honest about the cuts that go wrong first.

More posts by Otis

More in Upcycling

01doorganico 084goad 3hot8 4465456 after5internprogram ahandfulofblessings ahmadpc ahomcybersecurity allodialresources annodex antiquesandperiodcollectibles asianworldkashmir beedlectrics bloggertemplatefree bluefeatheragency bodyweightsolution campaign08blog carfixadvisor catstreetcollective cbstvsports cnfanspurchasing committeeof500yearsofdignityandresistance covertopsdjs cs-kaiyuangame cuestacomunicaciontotal cxoutlet dancebetgame deskgearhub destinyvillastay detectmagazine di33 diamondsteelbuildings donmo dyanadropship emarsysfinance emimattl escapechan eskitarih evautoplay everythingweddings-orlando farmzone feedviewerapp foxstudiosscratch gamevui123 gleasongrade greetingsday hacklabasu haskell iw-kaiyun jagoanproperti jilidskripsi joltbusinessfinance juegodepokergratis juegospucca kaeru-festival latestmehndidesigns lestanzediottaviano litemagazines localcommunityhero lustrsazan mariashebets menswheels newwebstechs1 nikkit ootheday oxigenvpn plurfitness prefetial probudgetcarpetcleaning psychicmrsmartin pyaten qvantor rejoignezlogis rexzbot riselayouts ruchin rwxqsgd5 sakaltime shibiaowang shop-bot skrtips spotlesshaven strcoding tetapatrium topselller uneplanteartificielle vipertechcr webtech1223411 wo-kygaming yamaha-mekar yeknava yoybuysheets zenunwa yamaha-mekar jilidskripsi ankertoto